If a Quick mode is initiated for a CHILD_SA that is already installed
we can identify this situation and rekey the already installed CHILD_SA.
Otherwise we end up with several CHILD_SAs in state INSTALLED which
means multiple calls of child_updown are done. Unfortunately,
the deduplication code later does not call child_updown() (so up and down
were not even).
Closesstrongswan/strongswan#95.
Reqids for the same traffic selectors are now stable so we don't have to
pass reqids of previously installed CHILD_SAs. Likewise, we don't need
to know the reqid of the newly installed trap policy as we now uninstall
by name.
This way we get the log message in stroke and swanctl as last message
when establishing a connection. It's already like this for the IKE_SA
where IKE_ESTABLISHED is set after the corresponding log message.
Fixes#2364.
These seem to indicate the major and minor version of the protocol, like
e.g. for the DPD vendor ID. Some implementations seem to send versions
other than 1.0 so we just ignore these for now when checking for known
vendor IDs.
Fixes#2088.
An old (already rekeyed) CHILD_SA would get switched back into CHILD_REKEYING
state. And we actually want to change the currently installed CHILD_SA to
that state and later CHILD_REKEYED and properly call e.g. child_rekey() and
not do this again with an old CHILD_SA. Instead let's only check installed
or currently rekeying CHILD_SAs (in case of a rekey collision). It's also
uncommon that there is a CHILD_SA in state CHILD_REKEYED but none in state
CHILD_INSTALLED or CHILD_REKEYING, which could happen if e.g. a peer deleted
and recreated a CHILD_SA after a rekeying. But in that case we don't want
to treat the new CHILD_SA as rekeying (e.g. in regards to events on the bus).
According to the mode-config draft there is no prefix sent for
IPv6 addresses in IKEv1. We still accept 17 bytes long addresses for
backwards compatibility with older strongSwan releases.
Fixes#1304.
When charon rekeys a CHILD_SA after a soft limit expired, it is only
deleted after the hard limit is reached. In case of packet/byte limits
this may not be the case for a long time since the packets/bytes are
usually sent using the new SA. This may result in a very large number of
stale CHILD_SAs and kernel states. With enough connections configured this
will ultimately exhaust the memory of the system.
This patch adds a strongswan.conf setting that, if enabled, causes the old
CHILD_SA to be deleted by the initiator after a successful rekeying.
Enabling this setting might create problems with implementations that
continue to use rekeyed SAs (e.g. if the DELETE notify is lost).
If we mistakenly detect a new IKE_SA as a reauthentication the client
won't request the previous virtual IP, but since we already migrated
it we already triggered the assign_vips() hook, so we should reassign
the migrated virtual IP.
Fixes#1152.
If we haven't received the third QM message for multiple exchanges the
return value of NEED_MORE for passive tasks that are not responsible for
a specific exchange would trigger a fourth empty QM message.
Fixes: 4de361d92c ("ikev1: Fix handling of overlapping Quick Mode exchanges")
References #1076.
In some cases the third message of a Quick Mode exchange might arrive
after the first message of a subsequent Quick Mode exchange. Previously
these messages were handled incorrectly and the second Quick Mode
exchange failed.
Some implementations might even try to establish multiple Quick Modes
simultaneously, which is explicitly allowed in RFC 2409. We don't fully
support that, though, in particular in case of retransmits.
Fixes#1076.
This is needed to handle DELETEs properly, which was previously done via
CHILD_REKEYING, which we don't use anymore since 5c6a62ceb6 as it prevents
reauthentication.
OpenBSD's isakmpd uses the latest ISAKMP SA to delete other expired SAs.
This caused strongSwan to delete e.g. a rekeyed SA even though isakmpd
meant to delete the old one.
What isakmpd does might not be standard compliant. As RFC 2408 puts
it:
Deletion which is concerned with an ISAKMP SA will contain a
Protocol-Id of ISAKMP and the SPIs are the initiator and responder
cookies from the ISAKMP Header.
This could either be interpreted as "copy the SPIs from the ISAKMP
header of the current message to the DELETE payload" (which is what
strongSwan assumed, and the direction IKEv2 took it, by not sending SPIs
for IKE), or as clarification that ISAKMP "cookies" are actually the
SPIs meant to be put in the payload (but that any ISAKMP SA may be
deleted).
Some clients like iOS/Mac OS X don't do a mode config exchange on the
new SA during re-authentication. If we don't adopt the previous virtual
IP Quick Mode rekeying will later fail.
If a client does do Mode Config we directly reassign the VIPs we migrated
from the old SA, without querying the attributes framework.
Fixes#807, #810.
The payload we sent before is not compliant with RFC 2407 and thus some
peers might abort negotiation (e.g. with an INVALID-PROTOCOL-ID error).
Fixes#819.
As we now use the same reqid for multiple CHILD_SAs with the same selectors,
having marks based on the reqid makes not that much sense anymore. Instead we
use unique marks that use a custom identifier. This identifier is reused during
rekeying, keeping the marks constant for any rule relying on it (for example
installed by updown).
This also simplifies handling of reqid allocation, as we do not have to query
the marks that is not yet assigned for an unknown reqid.
We currently send the notify in Main Mode only, as it is explicitly not allowed
by RFC 2407 to send (unprotected) notifications in Aggressive Mode. To make
that work, we'd need to handle that notify in Aggressive Mode, which could
allow a MitM to inject such notifies and do some harm.
Signed-off-by: Thomas Egerer <[email protected]>
I still think ipsec/l2tp with fragmentation support is a useful
fallback option in case the Windows IKEv2 connection fails because
of fragmentation problems.
Tested with Windows XP, 7 and 8.1.
When an initiator starts reauthentication on a connection that uses push
mode to assign a virtual IP, we can't execute the Mode Config before releasing
the virtual IP. Otherwise we would request a new and different lease, which
the client probably can't handle. Defer Mode Config execution, so the same IP
gets first released then reassigned during reauthentication.
If a peer immediately sends DELETE messages when completing Quick Mode rekeying,
the third Quick Mode message and the DELETE are sent simultaneously. This
implies that DELETE messages may arrive before the completing third Quick Mode
message.
Handle this case by ignoring the DELETE INFORMATIONAL in Quick Mode and let
the delete task handle it.
Similar to assign_vips() used by a peer assigning virtual IPs to the other peer,
the handle_vips() hook gets invoked on a peers after receiving attributes. On
release of the same attributes the hook gets invoked again.
This is useful to inspect handled attributes, as the ike_updown() hook is
invoked after authentication, when attributes have not been handled yet.
Tobias Brunner