Otherwise, we can't open a dedicated IPv4 socket on the same port as the
IPv6 socket already is set up do receive IPv4 packets (unless we'd again
enable SO_REUSEADDR).
Fixes: 83da133712 ("socket-default: Don't set SO_REUSEADDR on IKE sockets anymore")
This was originally required when pluto and charon both bound sockets to
the same port to send messages. Pluto also received messages on them but
charon didn't and used a raw socket instead. Since the removal of pluto
we don't need to set this option anymore, which might actually mask
mistakes like running charon and charon-systemd concurrently (that could
result in messages getting sent fine by both daemons but only received
by one).
Note that a failure to create/bind the sockets will not immediately
result in a shutdown of the daemon. Instead, there will be an error
once the receiver tries to read any messages and also whenever the sender
attempts to send a request.
There are a lot of calls like this:
this->dispatcher->raise_event(this->dispatcher, "...", 0,
b->finalize(b));
However, if finalize() fails, e.g. because a previous call to add()
failed due to the size limit, it returns NULL. This then caused a
segmentation fault in raise_event() when it interacted with that value.
Closesstrongswan/strongswan#1278
When watching the output of `swanctl -l` during debugging, the debug
messages in query_sa/policy() cause a lot of noise in the logs (level 2
for DBG_KNL still has actually useful information that we want to see
in the logs) and they're not very useful.
Compared to the messages in the functions above, the ones in update_sa()
and get_replay_state() are not seen often. But since there already is a
log message on level 2 in update_sa(), they're kinda redundant.
Closesstrongswan/strongswan#1271
Normally, GCC sees that we terminate the destination with a zero byte.
However, when using `-fsanitize=address`, there seems to be additional
instrumentation code after strncpy() so GCC produces warnings like
these:
‘__builtin_strncpy’ specified bound 16 equals destination size [-Wstringop-truncation]
Since the allocated data was smaller than sizeof(eap_mschapv2_header_t),
the following compile error was triggered (with newer GCC versions):
eap_mschapv2.c: In function 'process_peer_success':
eap_mschapv2.c:945:12: error: array subscript 'eap_mschapv2_header_t[0]' is partly outside array bounds of 'unsigned char[6]' [-Werror=array-bounds]
945 | eap->code = EAP_RESPONSE;
| ^~
In file included from /usr/include/stdlib.h:587,
from ../../../../src/libstrongswan/utils/printf_hook/printf_hook.h:26,
from ../../../../src/libstrongswan/library.h:101,
from ../../../../src/libcharon/sa/eap/eap_method.h:28,
from eap_mschapv2.h:27,
from eap_mschapv2.c:18:
eap_mschapv2.c:944:15: note: object of size 6 allocated by '__builtin_alloca'
944 | eap = alloca(len);
| ^~~~~~
Closesstrongswan/strongswan#1188Closesstrongswan/strongswan#1215
The previous code did not ensure that there was a delay of at least
`try` seconds after each sent request. Instead, whenever the condvar was
signaled, which could be due to retransmitted responses or messages for
unrelated transactions (there could even be spurious wakeups), the counter
was increased and a retransmit sent. So instead of actually waiting for
15 seconds for a response (and sending 4 retransmits over that timespan),
it could happen that all five messages were sent within a second without
enough time to actually receive a response.
Using an absolute timeout that we reuse as long as there was no timeout
and the condvar was signaled for something unrelated, should ensure we
wait at least the intended delay after each sent message.
Closesstrongswan/strongswan#1154
This allows using the upper parts of the marks for other purposes. For
instance, with `mark_in=mark_out=%unique/0x0000ffff` mark values in the
upper two bytes would not get reset by the rules installed by this plugin.
However, note that in this example the daemon would have to get restarted
after 65'535 CHILD_SAs to reset the counter for unique marks, which is a
global 32-bit counter that's unaware of any masks.
Closesstrongswan/strongswan#1087
mallinfo() is deprecated because it uses `int` for the members of the
returned struct, whereas mallinfo2() uses `size_t`. It's available
since glibc 2.33.
After establishing an IKE_SA, we check if any of its child configs
define generic SELinux labels and install trap policies for them if
necessary narrowed to the current (virtual) IPs.
This was originally added with 1551d8b13d ("kernel-netlink: reject
policy refcount if the reqid differs"). Since then we added code to
allocate constant reqids for the same TS, which pretty much avoids the
previous issues.
However, the reqid might have to be changed due to MOBIKE updates. And
because reqids are allocated for a complete set of traffic selectors and
not individual pairs, this can create a problem with drop policies as
those will use the old reqid (they are installed with the same priority,
reqid etc. to replace the actual IPsec policies), while unmodified
replacement policies will use the new one. A similar issue exists for
CHILD_SAs with SELinux contexts as those all use duplicate policies (same
generic label) but can't all be updated concurrently.
While combining the actions could cause duplicates (while the SA is
initiated, traffic might trigger the trap and the initiation of another
CHILD_SA), the previous commit should avoid most duplicates. If reuse_ikesa
is disabled, duplicates can't be prevented, though.
If a policy with IPComp template triggers an acquire, we get two, one for
an IPComp, one for ESP/AH SA. However, the triggering template of the trap
policy (where we get the reqid from), will be the same in both acquires,
IPComp, which we ignore, so no acquire was actually forwarded.
Such routes with a gateway that equals the peer's address are problematic
on FreeBSD. And since there is most likely a narrow route for the local
subnet anyway, the exclude routes would be redundant.
When installing routes based on remote traffic selectors, it can be
necessary to install an exclude route for the remote peer to avoid a
routing loop and continue to be able to reach it via IKE/ESP.
However, such routes are only necessary, if the routes we install don't
go via outbound interface. That's the case when using VIPs and routing
via TUN devices, or when using internal source IPs and routing via
their interfaces.
Installing such exclude routes if not necessary can cause issues on
FreeBSD (EINVAL when sending packets to the peer).
RFC3779 requires to validate the addrblocks of issuer certificates strictly,
that is, they must contain the extension and the claimed addrblock, up to
the root CA.
When working with third party root CAs that do not have the extension,
this makes using the plugin impossible. So add a depth setting that limits
the number of issuer certificates to check bottom-up towards the root CA.
A depth value of 0 disables any issuer check, the default value of -1
checks all issuers in the chain, keeping the existing behavior.
Closesstrongswan/strongswan#860
Without this, the authentication succeeded if the server sent an early
EAP-Success message for mutual, key-generating EAP methods like EAP-TLS,
which may be used in EAP-only scenarios but would complete without server
or client authentication. For clients configured for such EAP-only
scenarios, a rogue server could capture traffic after the tunnel is
established or even access hosts behind the client. For non-mutual EAP
methods, public key server authentication has been enforced for a while.
A server previously could also crash a client by sending an EAP-Success
immediately without initiating an actual EAP method.
Fixes: 0706c39cda ("added support for EAP methods not establishing an MSK")
Fixes: CVE-2021-45079
Tobias Brunner