Reqids for the same traffic selectors are now stable so we don't have to
pass reqids of previously installed CHILD_SAs. Likewise, we don't need
to know the reqid of the newly installed trap policy as we now uninstall
by name.
Otherwise, the remote identity is ignored when matching owner identities
of PSKs and this way matching PSKs that explicitly have %any assigned is
improved.
Fixes#2497.
This way we get the log message in stroke and swanctl as last message
when establishing a connection. It's already like this for the IKE_SA
where IKE_ESTABLISHED is set after the corresponding log message.
Fixes#2364.
If we find a redundant CHILD_SA (the peer probably rekeyed the SA before
us) we might not want to delete the old SA because the peer might still
use it (same applies to old CHILD_SAs after rekeyings). So only delete
them if configured to do so.
Fixes#2358.
This provides a solution for configs where there is e.g. a catch-all %any
PSK, while more specific PSKs would be found by the identities of configs
that e.g. use FQDNs as local/remote addresses.
Fixes#2223.
Some devices always use the oldest IKE_SA to send DPDs and will delete
all IKE_SAs when there is no response. If uniqueness is not enforced
rekeyed IKE_SAs might not get deleted until they expire so we should
respond to DPDs.
References #2090.
These seem to indicate the major and minor version of the protocol, like
e.g. for the DPD vendor ID. Some implementations seem to send versions
other than 1.0 so we just ignore these for now when checking for known
vendor IDs.
Fixes#2088.
By aborting the active task we don't have to wait for potential
retransmits if the other peer does not respond to the current task.
Since IKEv1 has no sequential message IDs and INFORMATIONALs are no real
exchanges this should not be a problem.
Fixes#1537
References #429, #1410Closesstrongswan/strongswan#48
Such a task is not initiated unless a certain time has passed. This
allows delaying certain tasks but avoids problems if we'd do this
via a scheduled job (e.g. if the IKE_SA is rekeyed in the meantime).
If the IKE_SA is rekeyed the delay of such tasks is reset when the
tasks are adopted i.e. they get executed immediately on the new IKE_SA.
This hasn't been implemented for IKEv1 yet.
Some peers send an INITIAL_CONTACT notify after they received our XAuth
username. The XAuth task waiting for the third XAuth message handles
this incorrectly and closes the IKE_SA as no configuration payloads are
contained in the message. We queue the INFORMATIONAL until the XAuth
exchange is complete to avoid this issue.
Fixes#1434.
An old (already rekeyed) CHILD_SA would get switched back into CHILD_REKEYING
state. And we actually want to change the currently installed CHILD_SA to
that state and later CHILD_REKEYED and properly call e.g. child_rekey() and
not do this again with an old CHILD_SA. Instead let's only check installed
or currently rekeying CHILD_SAs (in case of a rekey collision). It's also
uncommon that there is a CHILD_SA in state CHILD_REKEYED but none in state
CHILD_INSTALLED or CHILD_REKEYING, which could happen if e.g. a peer deleted
and recreated a CHILD_SA after a rekeying. But in that case we don't want
to treat the new CHILD_SA as rekeying (e.g. in regards to events on the bus).
According to the mode-config draft there is no prefix sent for
IPv6 addresses in IKEv1. We still accept 17 bytes long addresses for
backwards compatibility with older strongSwan releases.
Fixes#1304.
When charon rekeys a CHILD_SA after a soft limit expired, it is only
deleted after the hard limit is reached. In case of packet/byte limits
this may not be the case for a long time since the packets/bytes are
usually sent using the new SA. This may result in a very large number of
stale CHILD_SAs and kernel states. With enough connections configured this
will ultimately exhaust the memory of the system.
This patch adds a strongswan.conf setting that, if enabled, causes the old
CHILD_SA to be deleted by the initiator after a successful rekeying.
Enabling this setting might create problems with implementations that
continue to use rekeyed SAs (e.g. if the DELETE notify is lost).
If it was necessary to pass the local certificates we could probably
clone the config (but we don't do that either when later looking for the
key to actually authenticate).
Passing auth adds the same subject cert to the config over and over
again (I guess we could also try to prevent that by searching for
duplicates).
If we mistakenly detect a new IKE_SA as a reauthentication the client
won't request the previous virtual IP, but since we already migrated
it we already triggered the assign_vips() hook, so we should reassign
the migrated virtual IP.
Fixes#1152.