IKE_SA unique identifier allocation starts at 1. If the counter overflows,
a unique ID of 0 is assigned to an IKE_SA, which may have unclear consequences.
Overflowing the unique ID counter is theoretical for most setups, but on
a Gateway terminating 100'000 tunnels and rekeying the IKE_SA every 60s
overflows the counter after a month uptime. So avoid a 0 unique identifier
by using ref_get_nonzero().
Maintaining the reqid when recreating a CHILD_SA from scratch night not
strictly be necessary as we usually don't have to replace any temporary
states in the kernel. However, there could be concurrent acquires that
might actually make it necessary (we use the reqid to keep track of
acquires and it's also part of the duplicate check).
Keeping a reference ensures that if the old SA expires before the new
one is installed, the previous reqid isn't reallocated to a concurrently
established CHILD_SA with different selectors.
The reference is kept until the reqid is either confirmed (i.e.
re-allocated) or replaced by a different reqid, which happens only once
we know the final traffic selectors, or the SA is destroyed without
installing it.
Since the referenced commit, the state switch to IKE_ESTABLISHED doesn't
happen immediately after completing the authentication but only after
the remaining tasks have finished. Due to that redirects during IKE_AUTH
were treated like those during IKE_SA_INIT causing the IKE_SA and task
manager to get reset. However, unlike the ike-init task, the ike-auth
task returned SUCCESS and, therefore, got destroyed, while a different
task was removed from the array that was modified during the reset.
This later caused a dereference of the freed ike-auth task and a crash.
Fixes: 5ce1c91b58 ("ikev2: Trigger ike_updown() event after all IKE-specific tasks ran")
This works around an issue that occurs when recreating an IKE_SA with
multiple CHILD_SAs that use dynamically allocated reqids.
We currently try to preserve the reqid when reestablishing, so the
create-child task gets the reqid of the previous CHILD_SA and will try
to reallocate that once the CHILD_SA is installed. Before that, the old
CHILD_SA is destroyed and the reqid is released and added to the array
of reqids to get reused. However, because of the reverse order used here,
the first reqid in the array is the one of the last CHILD_SA.
So it can happen that a newly created CHILD_SA gets a reqid reassigned
that a later CHILD_SA will then also claim for itself and get assigned
because an entry with that reqid exists. So multiple CHILD_SAs with
different traffic selectors could then share the same reqid.
References strongswan/strongswan#1855
We track all IKE_SA_INIT requests as half-open IKE_SAs but didn't
correctly untrack them if their message ID or responder SPI was non-zero.
References strongswan/strongswan#1775
Fixes: b866ee88bf ("ike: Track unprocessed initial IKE messages like half-open IKE_SAs")
As specified in RFC 7296, section 2.25:
The SA that the initiator attempted to rekey is indicated by the SPI
field in the Notify payload, which is copied from the SPI field in
the REKEY_SA notification.
So we copy that and the protocol verbatim.
The calculation of the timeout is also shared now and the total
timeout in seconds is corrected in case retransmit_base is <= 1.
This could make it easier in the future to apply different retransmission
settings to messages/exchanges.
When we reset the initiator SPI, we have to migrate the adopted children
again so the correct IKE_SA can later be checked out.
Closesstrongswan/strongswan#1663
This forces the use of a semicolon after INIT() and makes existing ones,
which was the case for basically all instances, necessary so e.g.
sonarcloud won't complain about an empty statement after every one of
them.
By evaluating to the allocated object, it would theoretically also allow
constructs like this:
struct_t *this;
return INIT(this,
.a = x,
.b = y,
);
or this:
array_insert(a, ARRAY_TAIL, INIT(this,
.a = x,
.b = y,
));
This makes sure the event is only triggered after the IKE_SA is fully
established and e.g. virtual IPs, additional peer addresses or
a modified reauth time (on the initiator) are assigned to it. This was
e.g. a problem for the selinux plugin if virtual IPs are used.
We use a separate task to trigger the event that's queued before the
child-create task so the event is triggered before the child_updown()
event. Same goes for the state change to IKE_ESTABLISHED.
A new condition is used to indicate the successful completion of all
authentication rounds, so we don't have to set the IKE_ESTABLISHED state
in the ike-auth task (it was used as condition in other tasks).
Since set_state() also sets the rekey and reauth times, this required
some minor changes in regards to how AUTH_LIFETIME notifies are handled.
Since e334bd46b1 ("ike-auth: Move packet collection to post_build()
method") tasks and plugins can modify the IKE_SA_INIT message independent
of the ike-auth task.
Because flush() has to release the segment locks intermittently, threads
might add new entries (even with the change in the previous commit as the
IKE_SA might already be created, just not registered/checked in yet).
Since those entries are added to the front of the segment lists, the
enumerator in the previous step 2 didn't notice them and did not wait
for them to get checked in. However, step 3 and 4 then proceeded to
delete and destroy the entry and IKE_SA, which could lead to a crash
once the other thread attempts to check in the already destroyed IKE_SA.
This change combines the three loops of steps 2-4 but then loops over
the whole table until it's actually empty. This way we wait for and
destroy newly added entries.
Without ability to create SPIs, other threads are prevented from creating
new IKE_SAs while we are flushing existing IKE_SAs. However, there could
still be IKE_SAs already created that might get checked in while the
segments are temporarily unlocked to wait for threads to check existing
SAs in.
This is more consistent and e.g. allows to properly take into account
some settings that are also relevant during IKE_AUTH (e.g. childless).
We also already use the peer_cfg_t's ike_cfg_t when rekeying,
reauthenticating and reestablishing an IKE_SA (and e.g. for DSCP).
Also changed are some IKEv1 cases where get_ike_cfg() is called before
set_peer_cfg() without taking a reference to the ike_cfg_t that might
get replaced/destroyed (none of the cases were problematic, though, but
it also wasn't necessary to keep the ike_cfg_t around).
Closesstrongswan/strongswan#1238
This way we avoid having to pre-generate the message when it could
theoretically still get modified by a task that follows or from a plugin
via message() hook.
In particular as responder, this delays costly cryptographic operations
until the IKE_AUTH request is received, which is preferable to reduce
the impact of DoS attacks.
Another advantage is that the key material is not changed until all tasks
built or processed a message.
This way we avoid parsing messages with unexpected message IDs, which
might not even be possible if we don't have the keys anymore. However,
the next commit should avoid the latter and this way we avoid deriving
keys for retransmits or unexpected messages.
This also changes how retransmits for fragmented messages are triggered.
Previously, we waited for all fragments and reconstructed the message
before retransmitting the response. Now we only track the first
fragment and if we receive a retransmit of it respond immediately
without waiting for other fragments (which are now ignored). This is in
compliance with RFC 7383, section 2.6.1, and can avoid issues if there
are lots of fragments.
This way we can use the IKE_REKEYED state for both redundant and old SAs
to suppress ike_updown().
In the ike-delete task we don't suppress events in state IKE_REKEYING as
that's the case when we delete an SA the peer is currently rekeying with
multiple key exchanges.