With IKEv1 we transmit both public DH factors (used to derive the initial
IV) besides the shared secret. So these messages could get significantly
larger than 1024 bytes, depending on the DH group (modp2048 just about
fits into it). The new default of 2048 bytes should be fine up to modp4096
and for larger groups the buffer size may be increased (an error is
logged should this happen).
This is really only needed for other exchanges like DPDs not when we
just updated the addresses. The NAT-D payloads are only used here to
detect whether UDP encapsulation has to be enabled/disabled.
If we have to remove and reinstall SAs for address updates (as with the
Linux kernel) there is a short time where there is no SA installed. If
we keep the policies installed they (or any traps) might cause acquires
and temporary kernel states that could prevent the updated SA from
getting installed again.
This replaces the previous workaround to avoid plaintext traffic leaks
during policy updates, which used low-priority drop policies.
This can be useful if routing rules (instead of e.g. route metrics) are used
to switch from one to another interface (i.e. from one to another
routing table). Since we currently don't evaluate routing rules when
doing the route lookup this is only useful if the kernel-based route
lookup is used.
Resolvesstrongswan/strongswan#88.
The counter does not tell us what task is actually queued, so we might
ignore the response to an update (with NAT-D payloads) if only an address
update is queued.
Instead of destroying the new task and keeping the existing one we
update any already queued task, so we don't loose any work (e.g. if a
DPD task is active and address update is queued and we'd actually like
to queue a roam task).
This is currently not an issue for CHILD_SA rekeying tests as these only
check rekeyings of the CHILD_SA created with the IKE_SA, i.e. there is
no previous DH group to reuse.
For the CHILD_SA created with the IKE_SA the group won't be set in the
proposal, so we will use the first one configure just as if the SA was
created new with a CREATE_CHILD_SA exchange. I guess we could
theoretically try to use the DH group negotiated for IKE but then this
would get a lot more complicated as we'd have to check if that group is
actually contained in any of the CHILD_SA's configured proposals.
This way we get proper error handling if the DH group the peer requested
is not actually supported for some reason (otherwise we'd just retry to
initiate with the configured group and get back another notify).
This fixes two issues, one is a bug if a DH group is configured for the
local ESP proposals and charon.prefer_configured_proposals is disabled.
This would cause the DH groups to get stripped not from the configured but
from the supplied proposal, which usually already has them stripped. So
the proposals wouldn't match. We'd have to always strip them from the local
proposal. Since there are apparently implementations that, incorrectly, don't
remove the DH groups in the IKE_AUTH exchange (e.g. WatchGuard XTM25
appliances) we just strip them from both proposals. It's a bit more lenient
that way and we don't have to complicate the code to only clone and strip the
local proposal, which would depend on a flag.
References #2503.
IKE_SAs newly created via HA_IKE_ADD message don't have any IKE or peer
config assigned yet (this happens later with an HA_IKE_UPDATE message).
And because the state is initially set to IKE_CONNECTING the roam() method
does not immediately return, as it later would for passive HA SAs. This
might cause the check for explicitly configured local addresses to crash
the daemon with a segmentation fault.
Fixes#2500.
Otherwise, the remote identity is ignored when matching owner identities
of PSKs and this way matching PSKs that explicitly have %any assigned is
improved.
Fixes#2497.
If users want to associate secrets with any identity, let 'em. This is
also possible with vici and might help if e.g. the remote identity is
actually %any as that would match a PSK with local IP and %any better
than one with local and different remote IP.
Fixes#2497.
This allows us to use it without having to initialize libcharon, which
was required for the logging (we probably could have included debug.h
instead of daemon.h to workaround that but this seems more correct).
libstrongswan and kernel-netlink are the only two components which do
not adhere to the naming scheme used for all other tests. If the tests
are run by an external application this imposes problems due to clashing
names.
Signed-off-by: Thomas Egerer <[email protected]>
Tobias Brunner